Mikrotik wan failover script reddit. And it does for short term testing on my side.

Mikrotik wan failover script reddit. Part 2 - Script for "RB5009 - Initial success with dual ISP (Ziply & T-Mobile) load balancing & CAPSMAN" When I physically remove the cable from the main WAN the device fails over to the secondary WAN as expected. Mar 31, 2021 · In this case, basic failover won't handle switching to LTE interface because default route is still up because ISP's gateway is reachable. What do you think MikroTik Netwatch Failover with Dynamic WAN So i have a pretty good and reliable way of doing failover with a static internet connection and static gateway using netwatch to disable routes and then trigger a failover to use the secondary route in the routing table for internet. I'm looking for suggestions for a WAN failover setup on a RB750Gr3. This site has a fiber connection as its primary. Thanks! RB5009 WAN Failover Hi everyone. Hi all, I am bad at layer 3 stuff, so apologies if I'm missing some obvious things. It was a fairly complicated MikroTik script, a couple of hundred lines, that used several ping responders. Ping requests to the different responders were forced by routing marks to go out one src-natted gateway or the other. And traffic covered by your SimpleQueueList won’t be fasttracked either. Has anyone seen instructions to setup Dual WAN w/ failover when both ISPs are dhcp? Almost everything I am finding is showing to use static IPs which is not possible. And after the main link return, it wait stabilize for at least 2 minutes and check the response time again before reenable it. Has anyone attempted anything like this, or know of a way it might be possible? I used such a setup for several years. Jan 30, 2024 · Going out a WAN is already going to “break” fasttrack (and not covered by rule anyway). Unfortunately, both of my ISP (fiber and cable) will periodically renew my lease onto a wholly different gateway. I have an RB5009 that is used at a remote site for OOB management of on-site equipment. Mikrotik scripts for configuration with dual wan failover and load balancing - utrumo/mikrotik-scripts Jun 23, 2021 · I'm looking for suggestions for a WAN failover setup on a RB750Gr3. So how do I proceed from here? Hi, I want to have dual-WAN failover (main fiber on ether1, secondary LTE modem on ether5) and found a script which does exactly what I need, however… Ideally I'd like the router to run a script to check if the ping times via the wired connection to playstation's servers goes above 100ms, and automatically switch to the 5G connection until they return to normal. However if I sever the connection further down in the chain so the link is still up but the gateway can no longer be pinged, it doesn't failover. This means I can Jun 23, 2021 · I'm looking for suggestions for a WAN failover setup on a RB750Gr3. I have added a fiber handoff into the 5009 with a public IP off of this connection. Its WAN is plugged into an LTE device. Mikrotik scripts for configuration with dual wan failover and load balancing - utrumo/mikrotik-scripts. Jul 15, 2025 · In this article, we will look at another advanced method of failover using recursive routing and scopes from the routing section. In this case, basic failover won't handle switching to LTE interface because default route is still up because ISP's gateway is reachable. Unfortunately, both of my ISP (fiber and cable So I'll make four separate interface lists Uplink (set to wan interfaces, i have multiple uplink) LAN (Pppoe for clients) WAN (i keep it empty) Internet (i keep it empty) I have scheduled script that check down uplink using Internet list, and enable/disable routes automatically, if recursive gateway didn't catch it. So how do I proceed from here? Aug 13, 2023 · Hi, I want to have dual-WAN failover (main fiber on ether1, secondary LTE modem on ether5) and found a script which does exactly what I need, however… Ideally I'd like the router to run a script to check if the ping times via the wired connection to playstation's servers goes above 100ms, and automatically switch to the 5G connection until they return to normal. Recursive routing occurs when a route (either static or dynamically learned) has a next-hop that is not directly connected to the local router. We use Zerotier as our OOB VPN. 8 on the primary WAN. I was wondering what methods are you guys using that are up to date, known to work with latest routeros. Currently I'm using a Netwatch script that disables one WAN route while enabling the other whether there's a ping to 8. Mar 28, 2025 · I’ve read a whole bunch of prior art on these forums, reddit, and elsewhere on doing failover on mikrotik routers. 8. Mikrotik scripts for configuration with dual wan failover and load balancing - utrumo/mikrotik-scripts WAN Failover So, trying to get this failover setup with netwatch, but I'm completely stumped on why adding static routes for 2 internet-based DNS servers are not pingable. I've read a whole bunch of prior art on these forums, reddit, and elsewhere on doing failover on mikrotik routers. The default docs with recursive routing works reasonably well if I have a static gateway on my ISP. You can probably tack on a email monitoring script or syslog that connects via email or some monitoring that connects via a web api As an aside via the Mikrotik App from the appstore your internet connection status will also be displayed. I made a We would like to show you a description here but the site won’t allow us. This way, if the main link has a problem, in 1 second max the failover to STARLINK will be done. Does it create an entry in the log ? It will create an entry in the log. I have a custom script that will also beep when the connection status changes. There are many youtube and written tutorials\guides out there, some work, some stopped working with recent routeros versions or didn't work at all. Hi guys, I'm in need of configuring a RB951G with 2 WANs, one dynamic + one static with simple failover, no load-balancing. Has anyone attempted anything like this, or know of a way it might be possible? Jun 12, 2019 · I used such a setup for several years. And it does for short term testing on my side. uxpy mzmmnve lvschhng bhvyb sceo wyku fiuzm nxhy eyj hndh